Mark Levinson No 532 Amplifier - Store Demo
Precio habitual
$14,584.00
Precio habitual
$29,168.00
Precio de venta
$14,584.00
Precio unitario
por
Levinson is one of the most dependable brand names when it comes to high-end audio systems. For years the brand has been recognized by audiophiles throughout the world as equipment that delivers clear and consistent quality in music.
Specifications
- COMMUNICATION AND CONTROL:
- Two Link2 ports; one Ethernet port; one 3.5mm mono (tip/sleeve) mini plug trigger input, 3-12Vdc; one 3.5mm mono (tip/sleeve) mini plug trigger output, 3-12Vdc
- FREQUENCY RESPONSE:
- Within 0.1dB from 10Hz to 20kHz
- INPUT IMPEDANCE:
- 100 kΩ (balanced); 50 kΩ (unbalanced)
- INPUT SENSITIVITY:
- 2.83Vrms output at 130mVrms input
- RATED OUTPUT POWER INTO 8 OHMS:
- 400W/ch (20Hz to 20kHz at
- POWER REQUIREMENTS:
- 100V∼, 120V∼, 230V∼, 800W, factory set for destination country
- SPEAKER CONNECTIONS:
- Two “Hurricane” loudspeaker outputs with banana-plug sockets (banana-plug socket not available on the 230 VAC models)
- SIZE:
- HEIGHT – (with feet)- 9.55 in (242.57mm); (without feet)- 8.75 in (225.25mm) x WIDTH – 7.5 in (444.50mm) x DEPTH – 21.1 in (535.85mm)
- WEIGHT:
- Net weight- 121.5 lbs (55.22kg); Shipping weight- 129.5 lbs (58.86kg)"
What else to know about the Mark Levinson No. 532?
"The Nº 532’s meticulous craftsmanship is evident in the uniquely engineered design. To create the optimum power delivery system, the chassis of the Nº 532 is specially designed to isolate the audio circuits from interference and noise. When viewed from above, the rear portion of the power amplifier has three distinct piers. Control and power circuitry reside in the center pier, separate from the audio circuitry, which resides in the two outer piers – one dedicated to each channel. The power transformers are located at the front of the chassis, away from the audio circuits. This unusual design provides a number of important advantages – isolation of the potentially noisy power and control circuits from the delicate audio circuits, additional heat sink surface area for cooling, and very short signal and power delivery paths. Additionally, special care was taken in the design and implementation of the voltage regulator circuitry. Multiple stages of regulator circuits are employed, using a combination of series and shunt elements, custom-tailored to the audio circuitry for which they provide power. These discrete, low-noise, wide-bandwidth circuits are in close proximity to the audio signal path they power, but placed on a separate circuit board to minimize interaction with the audio signals and prevent corruption of low-level signals. The result is higher resolution, better bass definition, greater focus and more precise dynamic control. Similarly extraordinary measures were taken with the design of the toroidal power transformers, which filter mains-born noise from the secondary power supply and help ensure any capacitance that normally exists between the windings is knocked down to prevent it from finding its way into the delicate audio circuits. The power supplies are placed very close together to maximize magnetic field cancellation, and as far away from the audio signal path as possible to further reduce the potential for interference. The compact design of the Nº 532’s circuitry allows the signal path to be tighter and shorter, reducing parasitic capacitances and minimizing propagation delay and phase shift. The end result is a faster, wider bandwidth and a cleaner output signal with very low impedance level and minimal signal degradation. Lastly, the audio signal output path contains 24 output devices per channel, providing an impressive power capability while minimizing crossover distortion. The first non-reference Mark Levinson amplifier to be fully differential, the Nº 532 provides both RCA and XLR connectors that accept balanced signals directly into the input stage of the amplifier with no additional circuitry. Also, it is the first Mark Levinson linear amplifier to incorporate through-hole parts specifically for critical signal-path components and surface-mount components for building smaller circuits with higher performance. With the recent evolution of semiconductors, it is now possible to build more compact circuits, and obtain better transient response with greater stability and enhance immunity from noise sources. As music and cinema systems continue to grow more complex, integrating individual components takes on greater importance. To address the increasing demand for more control and communications capabilities, the Nº 532 features Mark Levinson’s proprietary ML Net and Link2 inter-device communication protocols, allowing the Nº 532 to be easily integrated and controlled by other Mark Levinson devices. The Nº 532 also provides a traditional 12V trigger input and output to synchronize on/standby status with other devices that do not include ML Net or Link2. An RS-232 port also allows the Nº 532 to be controlled by units from industry leaders such as AMX™, Crestron® and other third-party integrated control systems." - Mark Levison/CelloBrief History of Mark Levinson
Long mapped-to Binghamton New York – the current headquarters and manufacturing center for Mark Levinson Labs – not many people know the brand was originally launched outside of the Nation’s Capital in Silver Spring Maryland, in 1949. In 1956, the brand built their original facility in New York, according to the official brand website.